Welcome to the Water Rocket Forum, sponsored by The Water Rocket Achievement World Record Association.

Since our founding in 2003, we've become the largest, most sophisticated and ground breaking group supporting you, the serious water rocket flyer! Whether you are a beginner or an expert, the WRA2 has something for everyone.

A water rocket is a type of model rocket using water as its reaction mass. The pressure vessel (the engine of the rocket) is constructed from thin plastic or other non metallic materials (usually a used plastic soft drink bottle) weighing 1,500 grams or less. The water is forced out by compressed air. It is an example of Newton's third law of motion.

Twin barrel Water Rocket Launcher

Discussion about Compressors, hose, pipes, fittings, launchers, release mechanisms, and launch tubes.
Post Reply
User avatar
mahboob
WRA2 Member
WRA2 Member
Posts: 31
Joined: Tue Nov 25, 2014 2:15 pm

Twin barrel Water Rocket Launcher

Post by mahboob » Mon Dec 01, 2014 9:48 pm

Twin barrel Water Rocket Launcher for advance water Rocket
You do not have the required permissions to view the files attached to this post.



User avatar
U.S. Water Rockets
WRA2 Member
WRA2 Member
Posts: 398
Joined: Tue Jan 30, 2007 8:16 pm

Re: Twin barrel Water Rocket Launcher

Post by U.S. Water Rockets » Tue Dec 02, 2014 2:12 pm

mahboob wrote:Twin barrel Water Rocket Launcher for advance water Rocket
Does it fire both rockets at the same time so you can have a race to the top?



User avatar
RaketfuedRockets
WRA2 Member
WRA2 Member
Posts: 92
Joined: Sun Nov 30, 2014 5:01 pm

Re: Twin barrel Water Rocket Launcher

Post by RaketfuedRockets » Tue Dec 02, 2014 3:04 pm

That looks cool!
You should definitely try to launch two water rockets nearly at the same time, so that one rocket can film the launch of the other rocket from the air.


RaketfuedRockets - Building water rockets since 2011
Check out our YouTube-Channel: www.youtube.com/Raketfued
Check out our website: www.raketfuedrockets.com
Facebook Page: www.facebook.com/RaketfuedRockets

User avatar
Water Rocket Expert
WRA2 Member
WRA2 Member
Posts: 621
Joined: Fri Nov 22, 2013 10:39 am

Re: Twin barrel Water Rocket Launcher

Post by Water Rocket Expert » Tue Dec 02, 2014 6:22 pm

What kind of table was used? It looks like a standard kitchen, "island."


Water Rocket Expert
I'm 18
Maryland
"Anyone who has never made a mistake has never tried anything new." -Albert Einstein

User avatar
bugwubber
WRA2 Member
WRA2 Member
Posts: 1086
Joined: Wed Dec 19, 2012 2:47 am

Re: Twin barrel Water Rocket Launcher

Post by bugwubber » Wed Dec 03, 2014 2:41 pm

Gotta love the multi rocket launchers. My launcher releases them all at the same instant because they are all held in place by one steel bar that pivots out of the way. What is fascinating is how just changing the weight or amount of water has a large impact on acceleration as seen in below. For individual pull multi launchers, it is important to isolate the air line on each tube or a slight delay will vent all the pressure from one rocket. My launcher is normally left in the open position at each tube so there is no isolation but because they launch together, I rarely have problems with mislaunches. Those are normally caused by dirt getting in the rocket nozzle or launch tube.
DSC09880.jpg
You do not have the required permissions to view the files attached to this post.


Bugwubber

Team S.P.E.W.

User avatar
mahboob
WRA2 Member
WRA2 Member
Posts: 31
Joined: Tue Nov 25, 2014 2:15 pm

Re: Twin barrel Water Rocket Launcher

Post by mahboob » Wed Dec 03, 2014 5:50 pm

Once a launcher I have made same like your design. and control with pneumatic control and air pressure control with FRL device. also use with DRO for reading flight simulation with my special designed radar system every rocket data like achieve hight, flight duration quickly on my computer screen I upload pics very soon.



User avatar
bugwubber
WRA2 Member
WRA2 Member
Posts: 1086
Joined: Wed Dec 19, 2012 2:47 am

Re: Twin barrel Water Rocket Launcher

Post by bugwubber » Thu Dec 04, 2014 12:09 am

mahboob wrote:Once a launcher I have made same like your design. and control with pneumatic control and air pressure control with FRL device. also use with DRO for reading flight simulation with my special designed radar system every rocket data like achieve hight, flight duration quickly on my computer screen I upload pics very soon.
Oh I'd love to see that!


Bugwubber

Team S.P.E.W.

User avatar
U.S. Water Rockets
WRA2 Member
WRA2 Member
Posts: 398
Joined: Tue Jan 30, 2007 8:16 pm

Re: Twin barrel Water Rocket Launcher

Post by U.S. Water Rockets » Thu Dec 04, 2014 10:48 am

bugwubber wrote:Gotta love the multi rocket launchers. My launcher releases them all at the same instant because they are all held in place by one steel bar that pivots out of the way. What is fascinating is how just changing the weight or amount of water has a large impact on acceleration as seen in below. For individual pull multi launchers, it is important to isolate the air line on each tube or a slight delay will vent all the pressure from one rocket. My launcher is normally left in the open position at each tube so there is no isolation but because they launch together, I rarely have problems with mislaunches. Those are normally caused by dirt getting in the rocket nozzle or launch tube.
DSC09880.jpg
We developed a system to allow the staggered launch of multiple rockets. We inverted our one-way valve in each launch tube and use a slow fill rate when pressurizing. The slow fill does not produce enough pressure differential to activate the one way valve, so the rockets all fill normally. When launched, the one way valve in each launch tube will activate and prevent the pressure from escaping through any launched rockets launch tube.



User avatar
bugwubber
WRA2 Member
WRA2 Member
Posts: 1086
Joined: Wed Dec 19, 2012 2:47 am

Re: Twin barrel Water Rocket Launcher

Post by bugwubber » Thu Dec 04, 2014 1:44 pm

U.S. Water Rockets wrote:
bugwubber wrote:Gotta love the multi rocket launchers. My launcher releases them all at the same instant because they are all held in place by one steel bar that pivots out of the way. What is fascinating is how just changing the weight or amount of water has a large impact on acceleration as seen in below. For individual pull multi launchers, it is important to isolate the air line on each tube or a slight delay will vent all the pressure from one rocket. My launcher is normally left in the open position at each tube so there is no isolation but because they launch together, I rarely have problems with mislaunches. Those are normally caused by dirt getting in the rocket nozzle or launch tube.
We developed a system to allow the staggered launch of multiple rockets. We inverted our one-way valve in each launch tube and use a slow fill rate when pressurizing. The slow fill does not produce enough pressure differential to activate the one way valve, so the rockets all fill normally. When launched, the one way valve in each launch tube will activate and prevent the pressure from escaping through any launched rockets launch tube.
Interesting, so installed that way, it doesn't prevent emergency venting. Would you fill water through the line too or just air?


Bugwubber

Team S.P.E.W.

User avatar
U.S. Water Rockets
WRA2 Member
WRA2 Member
Posts: 398
Joined: Tue Jan 30, 2007 8:16 pm

Re: Twin barrel Water Rocket Launcher

Post by U.S. Water Rockets » Fri Dec 05, 2014 10:11 am

bugwubber wrote:
U.S. Water Rockets wrote:
bugwubber wrote:Gotta love the multi rocket launchers. My launcher releases them all at the same instant because they are all held in place by one steel bar that pivots out of the way. What is fascinating is how just changing the weight or amount of water has a large impact on acceleration as seen in below. For individual pull multi launchers, it is important to isolate the air line on each tube or a slight delay will vent all the pressure from one rocket. My launcher is normally left in the open position at each tube so there is no isolation but because they launch together, I rarely have problems with mislaunches. Those are normally caused by dirt getting in the rocket nozzle or launch tube.
We developed a system to allow the staggered launch of multiple rockets. We inverted our one-way valve in each launch tube and use a slow fill rate when pressurizing. The slow fill does not produce enough pressure differential to activate the one way valve, so the rockets all fill normally. When launched, the one way valve in each launch tube will activate and prevent the pressure from escaping through any launched rockets launch tube.
Interesting, so installed that way, it doesn't prevent emergency venting. Would you fill water through the line too or just air?
All of our 1-way valves have a USWR invention we call the "safety bypass bleed". It takes different forms depending on the design of the one way valve. The simplest form is one or more narrow grooves cut into the valve seat that prevents a 100% perfect seal. This allows the pressure to leak out slowly if the system must be depressurized for safety reasons. If the valve is part of a multiple stage rocket, the valve does leak but in the 5 or 10 seconds it needs to prevent air escaping during flight, the amount of pressure leaked is negligible. Well worth it to have the safety pressure drain feature it provides.

So even in the inverted position, the feature will allow the rockets to pressurize, albeit slowly.



User avatar
China_WaterRocket
WRA2 Member
WRA2 Member
Posts: 85
Joined: Fri Feb 10, 2017 9:36 am

Re: Twin barrel Water Rocket Launcher

Post by China_WaterRocket » Thu Mar 02, 2017 9:28 pm

RaketfuedRockets wrote:That looks cool!
You should definitely try to launch two water rockets nearly at the same time, so that one rocket can film the launch of the other rocket from the air.

Good idea


I come from China, do not understand English, your information I use the translation software to view. I like water rockets, technology is the same, I hope we can become friends.

User avatar
China_WaterRocket
WRA2 Member
WRA2 Member
Posts: 85
Joined: Fri Feb 10, 2017 9:36 am

Re: Twin barrel Water Rocket Launcher

Post by China_WaterRocket » Thu Mar 02, 2017 10:29 pm



I come from China, do not understand English, your information I use the translation software to view. I like water rockets, technology is the same, I hope we can become friends.

Post Reply