Not sure if anyone else has tried this, but I've found an easy (if not aerodynamically ideal) method to add a fairing/shroud to cover the tornado tube (or similar) coupler between 2-liters.
Unfortunately, the distance between the straight sides between two coupled 2-liter bottles is longer than the straight sided portion of a 2 liter (that you would use to harvest material to make a fairing). So to make a nice straight sided fairing, you will need to splice your 2-liters just to make the fairing - kind of a pain.
To simplify construction, I decided to use the straight portion of a 1-liter bottle since it's smaller diameter effectively shortens the amount of straight sided bottle required.
To make one, just find a straight sided 1-liter and carefully cut it down until it just barely fits snug once your coupler is fully tight. You need to be careful that you don't leave it too long or have irregular/rough edges or it will dent the 2 liter and may cause structural weakness in the 2-liter pressure vessel. I painted the inside of my fairings with spray paint to hide the couplers and add some flair...
Not sure how detrimental the hourglass effect is on the aerodynamics, but when properly fitted the fairing adds a lot of stiffness and integrity to the rocket which helps to keep it from kinking while handling on the ground.
-uberpixel
Easy fairing/shroud between 2 liters
-
- Advanced Member
- Posts: 24
- Joined: Sat Jun 07, 2014 12:11 pm
-
- WRA2 Member
- Posts: 1778
- Joined: Sat Feb 03, 2007 3:24 pm
Re: Easy fairing/shroud between 2 liters
Nice suggestion!uberpixel wrote:Not sure if anyone else has tried this, but I've found an easy (if not aerodynamically ideal) method to add a fairing/shroud to cover the tornado tube (or similar) coupler between 2-liters.
Unfortunately, the distance between the straight sides between two coupled 2-liter bottles is longer than the straight sided portion of a 2 liter (that you would use to harvest material to make a fairing). So to make a nice straight sided fairing, you will need to splice your 2-liters just to make the fairing - kind of a pain.
To simplify construction, I decided to use the straight portion of a 1-liter bottle since it's smaller diameter effectively shortens the amount of straight sided bottle required.
To make one, just find a straight sided 1-liter and carefully cut it down until it just barely fits snug once your coupler is fully tight. You need to be careful that you don't leave it too long or have irregular/rough edges or it will dent the 2 liter and may cause structural weakness in the 2-liter pressure vessel. I painted the inside of my fairings with spray paint to hide the couplers and add some flair...
Not sure how detrimental the hourglass effect is on the aerodynamics, but when properly fitted the fairing adds a lot of stiffness and integrity to the rocket which helps to keep it from kinking while handling on the ground.
-uberpixel
This is actually a very effective design because the smaller diameter bottle contacts the tapered portion of the two pressure vessel bottles at a point where it adds stiffness. If you use a bottle of the same diameter as the pressure vessel bottles, it does add stiffness, but not as much because when the rocket flexes the larger bottle tends to slide over the other bottle exterior and the opposite side gets loose because the shroud bottle pulls away from it. This is a good way to stiffen a long rocket with a lot of mass on either side of the tornado tube. We've used this in the past just for stiffening, but also with a real sized fairing on the outside so that the narrow part doesn't cause drag.
Team U.S. Water Rockets
Visit USWaterRockets.com
Visit our Blog
Tune in to our YouTube Channel
Visit our Facebook page
Visit our Twitter Page
Opportunity is missed by most people because it is dressed in overalls and looks like work. --Thomas Edison
Visit USWaterRockets.com
Visit our Blog
Tune in to our YouTube Channel
Visit our Facebook page
Visit our Twitter Page
Opportunity is missed by most people because it is dressed in overalls and looks like work. --Thomas Edison
-
- WRA2 Member
- Posts: 74
- Joined: Wed Feb 27, 2013 6:00 pm
Re: Easy fairing/shroud between 2 liters
Nice idea this "double" fairing, I might try it at my next rockets.
Thx
Thx
ptx